Constant voltage/current mode

  • I'm considering the CheapStat as a means to apply a constant potential (300mV) for a small photoelectrochemical cell while recording the current (tens of microamps range). Is this possible with the CheapStat?

  • @bojan I'm pretty sure the Cheapstat hardware is capable of doing what you want and there is a constant voltage test in the cheapstat firmware. Unfortunately, I don't think that the firmware for the constant voltage test is finished. In particular I don't think the firmware sends any data back to the PC after running the constant voltage test. Also, I'm not 100% sure, but I think the java GUI would need to modified as well to accept data from the device when performing the constant voltage test.

    I'm not the original author of the Cheapstat firmware. However I did at one point create a quick-and-dirty modification of the cheapstat firmware which adds a long duration constant voltage mode which might work for you. In this mode the cheapstat streams the data back to the PC as it is acquired. Note, the long duration constant voltage mode doesn't work with the standard GUI, instead it uses a command line based logger (a short python/pyserial program) to log the data as it comes in to the PC.

    The source code for this hack can be found here

    The project includes a makefile for building the firmware on linux.

    The added/modified function in the firmware which streams the data back to the PC is CONSTVOLT_long in firmware/cheapstat.c - starts at line 2583.

    The python/pyserial based command line logger is found in the logger sub-directory.

  • The Cheapstat firmware most certainly sends data ove the USB; it sends it as an 8-bit binary stream preceeded by the mode.
    It will also send the configurations as mode/config stream as a reply to any incoming USB data.

  • @WizWom Yes it is true that the cheapstat returns data via usb for the other tests e.g. LSV. However, this is not the case for the constant voltage test which I was referring to in my comment.

    In the firmware the function for the constant voltage test is CONSTVOLT_test in CheapStat_v2.c (starting at line 2543). I've attached the source code

    nt16_t CONSTVOLT_test (char* name, int16_t voltage, int16_t time) {
    	uint16_t elapsed;
    	int16_t current_DAC;
    	//check limits
    	if(voltage<-1600 || voltage>1600 || time<0 || time>9999)
    		lcdPrintData("outside limits",14);
    		return -1;
    	current_DAC = (int16_t) (round(voltage*(4096.0/3300))+2048);  
    	//init timer
    	//change switches
    	PORTE.OUTSET = PIN1_bm; //switch0
    	PORTE.OUTSET = PIN2_bm; //switch2
    	PORTE.OUTSET = PIN3_bm; //switch3
    	PORTE.OUTCLR = PIN0_bm; //switch1
    	//apply voltage
    	while (DAC_Channel_DataEmpty(&DACB, CH0) == false) {}
    	//start timer
    	TIMER.CNT = 0;
    	elapsed = 0;
    	while(elapsed < time) {
    		//wait for 1 sec
    		while(TIMER.CNT<1953) {}
    		//reset timer
    		TIMER.CNT = 0;
    		//increment elapsed
    	PORTE.OUTSET = PIN0_bm; //switch1
    	PORTE.OUTCLR = PIN1_bm; //switch0
    	PORTE.OUTCLR = PIN2_bm; //switch2
    	PORTE.OUTCLR = PIN3_bm; //switch3
    	current_DAC = 2048;
    	while (DAC_Channel_DataEmpty(&DACB, CH0) == false) {}
    	return elapsed;

    As you can see at no point in this function is any data sent to the host pc via the USART (using something like USART_PutCar).

    For a comparison you could look at the LSV_test function (line 2360). In particular starting after the comment "//start output to USB" (line 2493) you will see the section where data is sent back to the host PC using the USART_PutChar function.

    Note, I think it would pretty straight forward to modify the CONSTVOLT_test function so that it did send back data to the PC. Also, as another option, maybe it would be possible to mimic a constant voltage test by running one of the other tests with specific settings ?

  • @Will-Dickson you seem to be correct, although I can't fathom why you would run a test you can't get data from, that's not a test. It amounts to using the cheapstat as a voltage source.

Log in to reply