Awesome, thanks Will! got me up and running super quickly!

Just a small part of a project I'm working on but figured I'd share here. I needed to change some 10k manual pots to digital so I could automate it. I wrote the following Arduino sketch and the subsequent python wrapper to do just that. Hope this helps some!

Arduino Side basically just expects two spaced integers corresponding to the Potentiometer number [0-3] and the position you'd like [0-254] followed by a return (e.g. newline character \n):

#include "mcp4261.h"

// Example demonstrating how to use the MCP4261 library with
// the MCP4261 Arduino Uno V0.1 shield to change wiper 
// position based on serial input

int pot;
int wiper_pos;
const int POT_0_CS = 5;
const int POT_1_CS = 6;
const int LOOP_DELAY = 200;
MCP4261 pot0 = MCP4261(POT_0_CS);
MCP4261 pot1 = MCP4261(POT_1_CS);


void setup() {

    // Setup SPI communications
    SPI.setDataMode(SPI_MODE0);
    SPI.setBitOrder(MSBFIRST);
    SPI.setClockDivider(SPI_CLOCK_DIV8);
    SPI.begin();

    // Initialize potentiometers
    pot0.initialize();
    pot1.initialize();
    pot0.setWiper0(0);
    pot0.setWiper1(0);
    pot1.setWiper0(0);
    pot1.setWiper1(0);

    // Initialize Serial
    Serial.begin(9600);
    // Serial.println("Serial Ready...");
}


void loop()
{
 while (Serial.available() > 0) {
   pot = Serial.parseInt();
   wiper_pos = Serial.parseInt();
   if (Serial.read() == '\n') {
    switch (pot) {
      case 0:
       pot0.setWiper0(wiper_pos);
       Serial.print("Pot 0 set to "); 
       Serial.println(wiper_pos);
       break;
      case 1:
       pot0.setWiper1(wiper_pos);
       Serial.print("Pot 1 set to "); 
       Serial.println(wiper_pos);
       break;
      case 2:
       pot1.setWiper0(wiper_pos);
       Serial.print("Pot 2 set to "); 
       Serial.println(wiper_pos);
       break;
     case 3:
       pot1.setWiper1(wiper_pos);
       Serial.print("Pot 3 set to "); 
       Serial.println(wiper_pos);
       break;
     }
     wiper_pos = 0;
     Serial.flush();
   }
 }
}

The python class just gives you an easy way to connect to the the first found Arduino over serial and change the pot and value (requires pyserial, currently using 2.7) Will need to be modified for different Arduino boards and if there are multiple connected to the host:

#!/usr/bin/env python

###############################################################################
#
# Class to control IO Rodeo MCP4261 Potentiometer Shield
# http://iorodeo.com/collections/arduino-shields-and-breakout-boards/products/digital-potentiometer-shield
#
###############################################################################

import serial

from serial.tools import list_ports


class Controller(object):
    def __init__(self):
        '''Finds then sets up communication to connected Arduino'''
        self.port = self.find()
        self.baudrate = 9600
        self.timeout = 2
        self.pot_shield = self.connect(self.port)

    def find(self):
        '''Find a connected ECUsim and return its port'''
        for device in list_ports.comports():
            if device[1] == "Arduino Uno":
                port = device[0]
                return port
        else:
            print "Could not find a connected Arduino"
            return False

    def connect(self, port):
        '''Connect to a specified Arduino on [port]'''
        try:
            pot_shield = serial.Serial(port=port, baudrate=self.baudrate, timeout=self.timeout)
            return pot_shield
        except:
            print "Unable to connect to the Arduino at: {}".format(self.port)

    def turn_pot(self, pot, position):
        '''Send a command to the connected Arduino to turn a specific potentiometer [0-3] to a specific value [0-254]'''
        self.pot_shield.write("{} {}\n".format(pot, position))
        response = self.pot_shield.readline()
        return response.strip()

    def close(self):
        '''Close the communication to the ECUsim if the port is open'''
        if self.pot_shield.isOpen():
            self.pot_shield.close()
        return

Just received my pot shield and was wondering if there is an example Arduino sketch available to get me up and running quickly?

Thanks!